Connect BeagleBone Black to Cellular with Huawei E303 Modem

This tutorial will guide you through connecting a BeagleBone Black to the Hologram cellular network. The BeagleBone has some complications that make this a little more difficult than the Raspberry Pi:

• There is only a single USB host port, so you can’t plug in a keyboard and mouse at the same time as the modem without a USB hub.

• The default OS image does not support creating an Ethernet device for the modem in HiLink mode.

To get around the first issue, we’ll be using another PC for the bulk of the configuration, and using SSH over the USB client port to finish the setup. For the second issue, we’ll need to boot the BeagleBone off of a MicroSD card with a newer OS image on it.

Activate your SIM

If you haven’t already,
create a Hologram account
to manage your devices and billing. From the
Hologram Dashboard,
click the
Activate SIM
button in the top-right corner.

Every SIM card has an 18-22 digit unique ID printed on it. Enter your SIM’s ID in the activation form.

Then, choose your data plan and zone according to your needs. If you aren’t sure which plan is right for you, start with pay-as-you-go. See our
pricing page
for more details on plans and zones.

Set up the E303 Modem using another PC

The Huawei E303 USB modem is an extraordinary cellular modem for development and testing work. You can buy the E303 from
our online store.

The E303 supports two modes: in the default HiLink Mode, the device acts as a standard ethernet network interface, and you can configure the basic modem options through a web UI. In serial mode, the device exposes a low-level serial interface which allows for more control over the behavior of the modem.

HiLink Mode (Windows and MacOS)

• Slide the cover off of the Huawei E303 Modem and insert your Hologram SIM card with the full-size SIM insert.

• Plug the modem into your computer. The modem will mount itself as a storage device with the appropriate drivers on it. Install the drivers from the device, or download and install the latest drivers from the
  Downloads
  section of the
  E303 product page.

• When the install is finished, a web browser should automatically open to the Huawei HiLink settings page. If this doesn’t happen, navigate to
  192.168.1.1

• Click
  Settings->Profile Management->New
  and add a profile for the Hologram APN (
  hologram
  ) as shown here:

• Save all that and then go to the Connection Settings page. Enable all of the auto connect options as shown here:

• Finally click back to the Home page and click the connect button. You should now be connected to the internet via cellular.

HiLink Mode (Linux)

NOTE
: These steps assume a graphical interface so you can configure the modem via a web UI. If you are working with an embedded Linux device with only a command line interface, you can set up the profile on another computer, then plug the modem into the embedded device.

• Install the
  usb-modeswitch
  utility, which will handle switching the modem from storage mode to modem mode. For Debian-based distributions (e.g. Ubuntu and Raspbian), this package can be installed from the standard repositories with:

sudo apt-get update 

sudo apt-get install usb-modeswitch

• Then reboot your PC.

• Slide the cover off of the Huawei E303 Modem and insert your Hologram SIM card with the full-size SIM insert.

Then plug the modem into a USB port on your Linux machine.

• Run
  ifconfig
  to find the
  eth*
  device corresponding to the modem. If you are unsure which
  eth
  device is the right one, you can unplug the modem and see which one disappears when running
  ifconfig
  again.

• If the network interface doesn’t have an IP address assigned (no
  inet addr
  entry in
  ifconfig
  ), run the DHCP client to acquire an address:
  sudo dhclient eth1
  where
  eth1
  should be replaced with the modem’s device name.

• Open a web browser to
  192.168.1.1
  to configure the modem via web UI. Set up the Hologram APN profile and connection settings as described in the Windows/Mac instructions above, then click the
  Connect
  button on the device home page.

• Disable or unplug your PC’s other network connections (Ethernet or wireless), then test your internet connection:
  ping -c1 hologram.io

• If you get an error, you may need to add a route configuration so that network traffic is routed to the new cellular interface. From the command line, enter:
  sudo route add default gw 192.168.1.1 eth1
  where
  eth1
  should be replaced with the modem’s device name. Then retry the
  ping
  .

To automatically enable the modem whenever it’s plugged in and across restarts, you’ll need to modify the networking config. In Debian-based distributions, add the following lines at the end of the file
/etc/network/interfaces
:

allow-hotplug eth1

iface eth1 inet dhcp

Where
eth1
should be replaced with the modem’s device name.